[heatkiller]

Self mobs MCP 355's Heatsink ^^

Enjoy^^




installed

[r104_for]

Nice

[mikotan]

i guess my question will be... do you see any improvements in your idle and load temps?
whats the temp delta like with that mod?
Ive honestly never thought of doing that lol.

[heatkiller]

Originally Posted by mikotan

i guess my question will be... do you see any improvements in your idle and load temps?
whats the temp delta like with that mod?
Ive honestly never thought of doing that lol.

this mod is not on idle and load temps>>>

its actually help cool down & prolong the life on MCP355's

did u ever feel the 355 base heat b4??

it quite hot btw.. & i using 2X355 side by side
lucky i manage to find some Alu sink for it to let the air pass through from below
from front panel fan.

best is still get the 355 sit on the fan ^^ but no place for it^^

[F@|c0n]

hmm i put the pump behind my radiator .. but my radiator is 3x120 .. only cools my cpu haha so it will cool a bit of my pump .. but same like you, i bought lots of heatsink 1 about 75cents

[heatkiller]

Originally Posted by F@|c0n

hmm i put the pump behind my radiator .. but my radiator is 3x120 .. only cools my cpu haha so it will cool a bit of my pump .. but same like you, i bought lots of heatsink 1 about 75cents

nice bro ^^ better to cool it
cos the 355 base quite a hottie after 24hrs

[mikotan]

mines on 24/7... ill put a probe on it and see how hot it gets.
i remember it was just "warm" to the touch before when i touched it....
i might have to change my idea of pump heat depending on the results.
Thanks for the heads up.

Theres always the option of using a heatgel silicone on bottom also.
I dont think i have heatsinks that are large enough to accommodate the 355s.

[heatkiller]

bro i get it from some sec hand part VGA cooler sink

in SLS lucky i found it in Black color^^ last 2 pcs

[Fatfool]

haha!!

still missing the Fittings.

Well, i won't have to do that with mine.

as the entire case door is a large heatsink:


Not gotten my second pump to stick into that Dual DDC top but you get the idea how it'd look after I do so...

But i'm guessing that because of these heatsinks, you can't mount it vertically?

Oh. and our fittings are supposed to arrive soon right? Then you can finally put that whole pump set to good use!!

[heatkiller]

bro i still waiting for fittings^^ btw nice casing u have there^^

bro i will base mount it below infront the PSU ^^

[Fatfool]

Ah I see. Bolted down or just left sitting there? (will it move around if not bolted?)

Btw the fittings are apparently supposed to ship around 15 nov. Hopefully it does. Been waiting for a long time liao

[heatkiller]

it will be hold by tubings + psu wires force down....i will no bolt it ^^freestyle^^

cos i place my inlet/outlet of rad 360 downward front mounted

(noted i know it hard on bleeding air bubbie but will be fine for me) cos have method bleeding air bubbie

hopefully will arrive the Fittings let pray

BTW little update for u bro

these wll be my new babies Reaching End of this month




Selling my ex-babies
Bitspower compression + Rotaries fittings On-Sale !!!

[Fatfool]

Ah I see.

and Coloured Fittings?!?!!? Ok now that is something I haven't seen before...

And ah well, Can't use your old fittings cos unlike like everyone else here, I use 1/4" tubing due to the nature of my casing. The fittings I require should arrive with yours from the MO.