[bullydog]

Thanks for dropping by to visit my worklog, this is my first ever worklog in VR-Zone and I hope it turns out well.

Pls pardon me if my updates are kind of patchy or not in the correct built sequence as there were several things I had to juggle with
Whilst working on this project. You might notice that there are instances of incompleted areas not attended to whilst I’m working On something else, reason for that is because of time constraint juggling between work & personal commitments.

Firstly a big thank you to all those ppl involved in helping me one way or another in helping make this project happen.

Charles – From Murder Mod, who else but the Master Modder that helped provide the MurderMod aesthetics

Froze – As usual all his WC MO’s and poisonous stuff. Thanks bro

Sabe – Thanks for getting those YL Fans

Goondo – Thanks for Sharing the Freight

Uvnium (Gary) – Thanks for cutting the side Panel

IvesonGarnett – Valuable motherboard & OC Tips and advices along the way for both Rampage II Extreme & eVGA Classified Motherboard

Pissing_intel – For his valuable inputs too

Bianco sharing info over at XS

Everyone here at VR-Zone Thanks for your support

Lastly, I’m no photography expert I also don’t happen to own an SLR so pls pardon my novice photography skills

[bullydog]

eVGA Classified E761
As usual Poison from Froze Bro

[bullydog]

Nickel Plated HeatKiller 3.0 and 4870x2 WB done in Singapore
Apologies for the poor lightings

[bullydog]

[bullydog]

My small little set of fittings required for this built, definitely no match with some of our VR-Zone watercooling Gurus here

[bullydog]

YL Fans from Sabe

The workhorse for my Feser 360 and XSPC 240 Rads


Better Test it first prior to sleeving them


First Attempt of a sleeve job


Removed Molex plugs, might be using a fan controller instead

[bullydog]

Reserved for updates 6

[bullydog]

Reserved for updates 7

[bianco]

can i post or are you still reserving?
so that was your tj07 sidepanel that i saw last friday! i think. haha.
anyways, your stuff looks good bro. just noticed that you sleeved your fans all the way up to the 'motor',
do they still fit into the groove to be tucked away from the moving blades?

[Kozato]

Hey bro, care to share where you nickel plate your blocks?

Thanks in advance!

[bullydog]

Originally Posted by bianco

can i post or are you still reserving?
so that was your tj07 sidepanel that i saw last friday! i think. haha.
anyways, your stuff looks good bro. just noticed that you sleeved your fans all the way up to the 'motor',
do they still fit into the groove to be tucked away from the moving blades?

Thanks bro, actually i only realized that i only need to sleeve 3 fans right up to the motor and the other 2 fans up to the frame because 3 of the fans will be mounted on the Rad with a "pull" configuration and the other 2 will be pushing air thru the rads. Looks like there's some work to be done to re-sleeve 2 fans

[sabe]

Looking good man! Can't wait to see the rest of it

@bianco - I had the same difficulties, I ended up cutting a bigger hole to let the wires through.

[bullydog]

Originally Posted by Kozato

Hey bro, care to share where you nickel plate your blocks?

Thanks in advance!

Here you go

That's Electroplating Pte Ltd
18, Third Lok Yang Road, Singapore 628011
Ph : 6265 9479 ; Fax : 6268 5361
Email : thats@singnet.com.sg

Originally Posted by sabe

Looking good man! Can't wait to see the rest of it

Thanks Boss

[Kozato]

Originally Posted by sabe

Looking good man! Can't wait to see the rest of it

@bianco - I had the same difficulties, I ended up cutting a bigger hole to let the wires through.

Time to take out the dremel hahaha....

@bullydog:

Thanks, mind sharing with me how much you paid to nickel plate those blocks?

[bullydog]

Originally Posted by Kozato

Thanks, mind sharing with me how much you paid to nickel plate those blocks?

I think I paid around $40 for each block